Table of Contents
A Consumer Guide to Product Safety
Quick Start
1
2
Attaching the Remote and Mounting Bracket
Controls and Indicators
Using the iH85
3
4
5,6
6
Charging your iPod
Listening to iPod
6
Batteries Installation
6
A Consumer Guide to Product Safety
Trouble Shooting
7
8
Solución De Problemas
Warranty Information
9
10
Package Contents
Congratulations on your iH85 Cycler bicycle speaker system for the iPod. Before you set up your unit,
please check to see that the package contains the following items:
1 Main Unit
1 AC Adaptor
1 Mounting bracket
2 Hex head mounting screws
1 Remote control with mounting clamp and 2 CR2032 batteries (installed)
3 iPod inserts
1 Audio patch cord
1 Carry bag
Maintenance
•
•
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should
be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or
similar materials can damage the surface of the unit.
A Consumer Guide to Product Safety
IMPORTANT SAFETY INFORMATION: IT IS THE USER'S RESPONSIBILITY TO USE THIS PRODUCT PRUDENTLY,
RESPONSIBLY AND IN A SAFE, NON-DISTRACTED MANNER AT ALL TIMES. FAILURE BY THE USER TO PAY
FULL ATTENTION TO THE PROPER OPERATION OF ANY EQUIPMENT BEING USED ALONG WITH THIS
PRODUCT COULD RESULT IN AN ACCIDENT AND/OR PERSONAL INJURY.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
1
iH85 Quick Start
1:Opening and Closing
2:Power: AC or Batteries
1
RESETR E S E T
T E S T
2
To charge and play iPod, attach AC adaptor to jack at
waist of the iH85 (under rubber tab) and plug the other
end into a working AC outlet. Does not charge batteries.
For portable operation (on bike, etc.), open the battery
door located inside the unit behind the iPod dock.
Install 4 AA batteries (match + and - polarity in diagram).
1. Twist the top half of the case as shown
2. Lift off.
When the case is open, you can change batteries
and access (dock and undock) your iPod.
To close the case, place case halves together and
twist until arrows align.
Your iH85 comes
Thick iPod
(no Insert needed)
with
3
inserts to
Mini Insert
Thin iPod Insert
iPod 4G 20 GB
iPod Photo 20/30 GB
5G iPod w/ Video 30 GB
Nano Insert
ensure your iPod fits
properly in the dock.
Note: Thick iPod
models dock without
insert
Use with
iPod Mini
iPod 4G
iPod Photo
5G iPod w/ Video 60/80 GB
40 GB
iPod Nano
2/4/8 GB
60 GB
3:Docking a Thin
4:Docking a Nano 5:Playing iPod
or iPod Mini
iPod
2
1
1
1
2
2
1. Gently slide the Thin iPod insert
into the dock.
2. Carefully place your iPod onto the
dock connector. The iPod must
not be in a case or “skin”.
1. Gently guide the nano or mini onto
the connector pins in the dock
2. Slide the nano insert over the
docked nano OR the mini insert
over the docked mini
Insert iPod into dock with proper insert
as needed. When running on AC
power, the iPod will charge while
docked. Press the Power Button on
the iH85 to play iPod.
2
Attaching the Remote Clamp and Mounting Bracket
1:Mounting Remote Clamp To Handlebars
2:Attach Remote To Clamp
C
A
B
a) Using Phillips screw driver, open mounting clamp.
To attach the iH85 remote, slide the mounting slot on
back of the remote down the square top of the clamp
until it clicks. Press clip button to release. Do not leave
remote on bike when unattended.
b) Wrap mounting clamp around handle bar. The square top
should face the bicycle seat
d) Tighten clamp using a Phillips screwdriver
3:Mounting Bracket
A
Attaching the Mounting Bracket
a) Align bracket with existing bottle
bracket holes on down tube
b) Screw bracket firmly to down tube
with hex (Allen) wrench until
securely fastened
To attach the iH85, slide it into the
bracket with the Power button
facing you and the speaker facing
up.
B
3
Controls and Indicators
Remote Panel
ᕥ Volume Increase
ᕤ Forward Button
ᕡ Reverse Button
ᕢ Volume Decrease
ᕣ Play / Pause Button
™
Back Panel
Front Panel
Remote for easy storage
Remote for easy storage
During use, place the
end cap on the bottom
of the iH85. When not
in use, place the end
cap on top to protect
the speaker.
ᕦ Power Button
ᕧ AC Adaptor Jack
ꢀ End Cap
ꢀ End Cap
4
To dock a thin iPod model
1. Gently slide the thin iPod insert into the dock
2. Carefully place your iPod within insert onto connector in the dock
To dock a nano or mini iPod model
1. Gently slide the nano or mini iPod onto the connector pin in the dock.
2. Carefully slide the nano insert over the docked nano or the mini insert over the docked mini
Charging your iPod
NOTE: Please make sure your iPod is docked correctly using the correct insert (see above) . Failure to do so may damage
your iPod.
1. While your iPod is docked in the unit and the unit is connected to AC power, it charges the iPod (until fully charged).
iPod will not be charged when using battery power.
2. The LED indicator will flash to show the iPod is charging. During iPod play, the LED stays on.
Listening to iPod
1. If you dock an already-playing iPod, the iH85 will automatically turn on and you will hear music playing from your iPod.
NOTE: If the loudness of the music is too low on the iPod itself, iH85 may not detect the iPod is in play mode. Press
ꢁ
the
Power Button to play it.
2. When the iPod is docked and in standby mode, press the Power On/Off Button on the iH85 to play it. The LED indicator
will stay on to show the power is on.
ᕣ
ᕥ
3. Press the
4. Press the
Play/Pause Button on the remote control to pause play; press again to resume it.
ᕢ
Volume + and
Volume – Button on the remote control to adjust the system volume.
ᕤ
ᕡ
5. Press >> or << Button on remote control to go to the next or previous track. Press and hold while track is playing
for high speed forward or reverse music search of the current track.
ᕦ
6. To turn off the iH85, press the
Power on/off Button. If the unit is connected to AC outlet, your iPod will continue
charging while in the dock. You cannot power off the unit using the remote control.
Batteries Installation
Install/Replace the Remote Control Batteries
The remote control batteries are already installed at the factory. When the remote control
stops operating or its range seems reduced, replace the batteries with new ones.
1. The battery compartment cover is located on the bottom of the remote control.
2. Use a Phillips screwdriver to unscrew the retaining screw on the battery compartment
cover.
3. Turn the battery compartment cover counterclockwise slightly to unlock the battery
cover. Remove the cover.
4. Insert 2 CR2032 batteries, checking the + and – sides of the batteries match the
diagram inside the battery compartment.
5. Replace the battery cover, turn clockwise to lock and replace the retaining screw.
NOTE: Make sure you dispose of batteries properly (see your local regulations).
6
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to assure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use. Keep these instructions handy for future reference. Take special note, and adhere to all warnings
on the unit and in the instruction and service manual.
1. Water and Moisture - The unit should not be used near water. For example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, etc., when using the AC adaptor.
2. Ventilation - The unit should be situated so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed
in a built-in installation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings.
3. Heat - The unit should be situated away from heat source such as radiators, heat register, stoves, or other appliances
(including amplifiers) that produce heat.
4. Power Sources - The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power Cord Protection – Power supply cord should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cord exits the unit to where
it is plugged into an AC outlet.
6. Cleaning - The unit should be cleaned only as recommended by the manufacturer.
7. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through openings.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall outlet and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
11. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A. The power-supply cord or plug has been damaged.
B. Objects have fallen into or liquid has been spilled into the enclosure.
C. The unit has been exposed to rain.
D. The unit has been dropped or the enclosure damaged.
E. The unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power
cord should be unplugged and take out batteries from the unit to prevent damage or corrosion.
13. Servicing - The user should not attempt to service the unit beyond that described in the user’s operating instructions.
All other servicing should be referred to qualified service personnel.
7
Trouble Shooting
Possible Problem
Solution
Symptom
Unit doesn’t respond
(no power)
AC adaptor isn’t plugged to a wall outlet or the
connector is not plugged into the power supply jack
on the back of the unit.Plug the AC adaptor into a
wall outlet and plug the connector into the AC jack
on the unit
Plug the AC adaptor into a wall outlet and plug the connector into the AC
jack on the unit
Plug another device into a wall outlet (same outlet) to confirm the outlet is
working
Wall outlet is not functioning
Batteries are weak or dead on unit or remote
Replace all the batteries with new ones
Press the Power button on the iH85
Power is off
Using no or wrong iPod insert
Make sure the dock insert is the proper fit to your iPod
iPod does not dock
properly
Remove your iPod from the dock and check for obstruction on the connectors
in the dock and on your iPod. Then reseat it in the dock.
iPod is not installed properly
Remove your iPod from the dock and check for obstruction on the connectors
in the dock and on your iPod. Then reseat it in the dock.
iPod is not installed properly
Your iPod software is too old
iPod does not respond
to the unit
Upgrade software on your iPod. For details, visit
Please make sure your iPod is working properly before dock into the unit.
Please refer to your iPod manual for detail.
iPod is locked up/frozen
iPod didn’t charge up
Make sure unit is plugged into working outlet and all connections are good
Unit is not plugged into a working AC outlet
iPod is not installed properly
Remove your iPod from the dock and check for obstruction on the connectors
in the dock and on your iPod. Then reseat it in the dock.
Using 3rd generation iPod
iPod is locked up/frozen
iH85 does not support 3rd generation iPod
Please make sure your iPod is working properly before docking in the unit.
Please refer to your iPod manual for detail.
iPod battery has problem
Volume level is set too high
Decrease the volume
Sound is distorted
If iPod original sound source is poor quality, distortion and noise are easily
noticed with high-power speakers.
Sound source is distorted
Try turning bass boost OFF
Make sure end cap or remote is not covering speaker during use
Replace with new batteries
Batteries are weak/ dead
Remote Control didn’t
work
Move the Remote Control closer to main unit
Remote Control is too far way from main unit
NOTE: When AC adaptor is plugged in, your iPod
will charge (with or without batteries installed).
NOTE: Unit does not control or charge 3G iPod
8
Solución De Problemas
Posible Problema
Solución
Síntoma
El adaptador de correinte alterna no esta
connectado a la unidad o no enchufado al la
esplalda de la unidad. Tape el adaptador CA a un
oulet de pared y tape el connector en el gato de
corriente alterna del unidad.
Enchufe el adaptador de corriente alterna al toma corriente y enchufe el
connector al gato de corriente alterna en la unidad.
La Unidad no responde
(no hay poder)
Tomacorriente no funciona
Enchufe otro aparato(mismo oulet) para segura que hay corriente.
Reemplace todas Pilas con nuevos.
Los pilas son debil o muerto en la unidad o el
remoto.
El poder está apagado
Apriete el botón del poder en el IH85
cerciórese la adición de dársena es el ataque apropiado a su iPod
iPod no atracar
apropiadamente
No esta utilizando las adiciones correctos o sin
ningun metes.
Quite su ipod de la dársena y el cheque para el obstuction en los conectores
en la dársena y en su ipod. Entonces acomodarlo en la dársena.
iPod no es instalado apropiadamente
iPod no es instalado apropiadamente
Su software de Ipod es demasiado viejo.
iPod es cerrado/congelado
Quite su ipod de la dársena y el cheque para el obstuction en los conectores
en la dársena y en su ipod. Entonces acomodarlo en la dársena.
iPod no responde a la
unidad.
mejore software en su ipod para detalles visita ;
http//ww.apple.com/ipod/download
Cerciórese por favor su Ipod trabaja apropiadamente antes de dársena en
la unidad. Para más detalles, consulte el manual de su iPod.
La unidad no es tapada en un oulet de trabajo de
C.A.
Cerciórese la unidad esta enchufada en un tomacorriente que trabaja y
todas conexiones son buenas..
iPod no cargó arriba
iPod no es instalado apropiadamente
Quite su ipod de la dársena y el cheque para el obstuction en los conectores
en la dársena y en su iPod. Entonces acomodarlo en la dársena.
ipod no sostiene la generacion tercera
Utilizando iPod tercero de generacion
iPod es cerrado/congelado (iPOD is locked or
frozen)
La batería de iPOD tiene el problema )
Cerciórese por favor su Ipod trabaja apropiadamente antes de dársena en
la unidad. Para más detalles, consulte el manual de su iPod.
El sonido es retorcido
Telemando no trabaja
el nivel puesto del volumen es muy alto.
La fuente sano es retorcida
bajar de volumen.
Si la original de ipod la fuente sano es la mala calidad, la deformación y
sonido son advertidos fácilmente con oradores de alto-poder.
Trate la sintonía del empujo bajo.
Cerciórese la tapa final o el telemando no cubren a orador durante el uso.
las baterías son débiles o muertas.
Instale nuevas pilas.
Mueva el telemando a distancia más cerca a la unidad
el Telemando distancia está demasiado lejos
de la unidad principal.
NOTA: Cuando el adaptador AC está conectado, su iPod
se cargará (con o sin las pilas instaladas).
NOTA: La unidad no controla o carga iPod de 3a Generación
Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects
in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should this
fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies will
repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage, and
insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed
below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is $30.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries are
the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Drive
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which have
been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized persons; (ii)
cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes (if applicable); (iv)
the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser.
In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members or agents be liable
to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do
not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may not apply to you.) This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding
to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product.
© 2007 SDI Technologies, Inc. All rights reserved
or call 1-800-288-2792 Toll Free
IH85-012407-A (USB)
Printed in China
10
|